Preparation and Properties of an Efficient Purification Material for Personal Protection

At present, the filtration of virus and other small particles in the air by meltblown cloth produced by electret treatment mainly depends on its electrostatic adsorption mechanism. However, because the surface charge of melt blown fabric can not be maintained for a long time, it can not maintain high efficiency filtration for a long time. Therefore, there is no guarantee for the medical staffs to not be infected by COVID-19. Therefore, it is necessary to improve the mechanical filtration efficiency of melt blown fabric in the situation of an electric charge loss. In this paper, nylon 6 (PA6) nanofibers were electrospun on melt blown cloth by electrospinning technology, and a sandwich material with melt blown cloth as surface layer and PA6 nanofibers as middle layer was made by hot- pressing technology;the surface morphology, thermal and mechanical properties of the sandwich material were characterized, and its filtration performance was tested. The experimental results show that the surface integrity of the sandwich material is high, and the diameter of nanofibers can reach about 67 nm;without the electret treatment, the filtration efficiency of the sandwich material for particles in an size of 0.2 μm is more than 95%,while the filtration efficiency of non-woven fabric is zero;the filtration resistance of the material is about 284 Pa, which is suitable for personal protection. © 2023 Chengdu University of Science and Technology. All rights reserved.

Electrospun Polymer Nanofibers for Technology Applications: A Short Review

Nanofibers are a type of nanomaterial with a diameter ranging from ten to a few hundred nanometers with a high surface-to-volume ratio and porosity. They can build a network of high-porosity material with excellent connectivity within the pores, making them a preferred option for numerous applications. This review explores nanofibers from the synthesis techniques to fabricate nanofibers, with an emphasis on the technological applications of nanofibers like water and air filtration, photovoltaics, batteries and fuel cells, gas sensing, photocatalysis, and biomedical applications like wound dressing and drug delivery. The nanofiber production market has an expected compound annual growth rate (CAGR) of 6% and should reach around 26 million US $ in 2026. The limitations and potential opportunities for large-scale applications of nano-fibrous membranes are also discussed. We expect this review could provide enriched information to better understand Electrospun Polymer Nanofiber Technology and recent advances in this field. © 2023 Bentham Science Publishers.

Supramolecular Nanofibers Block SARS-CoV-2 Entry into Human Host Cells.

The severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) infection relies on its spike protein binding to angiotensin-converting enzyme 2 (ACE2) on host cells to initiate cellular entry. Blocking the interactions between the spike protein and ACE2 offers promising therapeutic opportunities to prevent infection. We report here on peptide amphiphile supramolecular nanofibers that display a sequence from ACE2 in order to promote interactions with the SARS-CoV-2 spike receptor binding domain. We demonstrate that displaying this sequence on the surface of supramolecular assemblies preserves its α-helical conformation and blocks the entry of a pseudovirus and its two variants into human host cells. We also found that the chemical stability of the bioactive structures was enhanced in the supramolecular environment relative to the unassembled peptide molecules. These findings reveal unique advantages of supramolecular peptide therapies to prevent viral infections and more broadly for other targets as well.

Cerium Oxide Nanoparticles/Polyacrylonitrile Nanofibers as Impervious Barrier against Viral Infections.

BACKGROUND: Using face masks is one of the protective measures to reduce the transmission rate of coronavirus. Its massive spread necessitates developing safe and effective antiviral masks (filters) applying nanotechnology. METHODS: Novel electrospun composites were fabricated by incorporating cerium oxide nanoparticles (CeO2 NPs) into polyacrylonitrile (PAN) electrospun nanofibers that can be used in the future in face masks. The effects of the polymer concentration, applied voltage, and feeding rate during the electrospinning were studied. The electrospun nanofibers were characterized using SEM, XRD, FTIR, and tensile strength testing. The cytotoxic effect of the nanofibers was evaluated in the Vero cell line using the MTT colorimetric assay, and the antiviral activity of the proposed nanofibers was evaluated against the human adenovirus type 5 (ADV-5) respiratory virus. RESULTS: The optimum formulation was fabricated with a PAN concentration of 8%, w/v loaded with 0.25%, w/v CeO2 NPs with a feeding rate of 26 KV and an applied voltage of 0.5 mL/h. They showed a particle size of 15.8 ± 1.91 nm and a zeta potential of -14 ± 0.141 mV. SEM imaging demonstrated the nanoscale features of the nanofibers even after incorporating CeO2 NPs. The cellular viability study showed the safety of the PAN nanofibers. Incorporating CeO2 NPs into these fibers further increased their cellular viability. Moreover, the assembled filter could prevent viral entry into the host cells as well as prevent their replication inside the cells via adsorption and virucidal antiviral mechanisms. CONCLUSIONS: The developed cerium oxide nanoparticles/polyacrylonitrile nanofibers can be considered a promising antiviral filter that can be used to halt virus spread.

Biodegradable Bio-based Material for Wearable Air Filtering Skin

COVID-19, imagine having a temporary lip sticker that offers the protection of an n95 mask without the uncomfortable bulk. Using green electrospun nanofibers the lip sticker filters the virus and can communicate geospatial data to your phone using embedded NFC technology. Available in different designs and skins, some fiber formations can display temperature changes on your face. This paper investigates several prototypes of the described product. © 2022 Owner/Author.

Advances in medical textiles

Medical textile is one of the technical textiles sectors, growing faster due to developments in polymer science and technology and innovation in forming new textile structures. In this review, current market trends for the growth of medical textiles for both pre and post covid pandemic periods were discussed. Focus is given to the classification of medical textiles and devices, specific requirements of fibers and widely used types of fibers, and advanced developments in this field, including nanofibers, bicomponent fibers, superabsorbent polymers, and conductive materials used in a wide range of advanced medical devices. Various fabric structures (woven/knitted/nonwoven/braided) have been in use in biomedical devices;however, recent 3D shaped structures such as spacer fabrics, and 3D-printed materials have profoundly marked their significance with its ability to adapt to specific needs of the medical community. Smart wearable sensor technologies for monitoring, diagnosis, and treatment are discussed and critically reviewed, enabling the readers to understand the complexity of the nature of interdisciplinary approaches required for developing such complex structures and systems. Antimicrobial agents (synthetic and natural/organic) used in the development of medical textiles mainly wound dressings, advances in antiadhesive textile coatings, and antimicrobial assessments of medical fabrics are critically reviewed. Finally, a case study on 3D printing of complex structures is presented to update modern developments using fine detail resolution (FDR), a selective laser sintering that uses carbon dioxide laser to produce delicate and complex 3D structures suitable for medical applications. It is anticipated that readers will benefit from this critical overview of trends in this sector and the multidisciplinary approaches needed to meet the demands of the ever-growing consumer base. © 2023 Elsevier Ltd. All rights reserved.

Life Cycle Assessment of Nanofibrous Air Filtering Materials and Respirators

The current spread of COVID-19 pandemics resulted in a surge of a need of respiratory protection devices, including medical facemasks and facepiece respirators. Large amounts of products based on nonwoven filtration material from non-renewable petroleum based plastics (polyethylene) has raised global concerns about excessive environmental impacts of these products. Unfortunately, the replacement of polypropylene nonwoven microfibre based single use masks by the multiple use products did not appear as an effective strategy due to a lower filtration performance, although potentially lower environmental impacts. Nanofibre based filtration devices introduce themselves as potentially more environmentally friendly ones due to a lower overall usage of raw polymer compared to microfibrous ones. We present the LCA modelling of environmental impacts of respiratory protective devices with nanofibrous filter materials and compare those against traditional micro fibrous materials (FFP1 and FFP2 respirator) and medical facemask. Generally, due to a lower mass of nanofibre, these products emerge as a better environmental option, providing similar protection level. © 2022 17th International Conference on Indoor Air Quality and Climate, INDOOR AIR 2022. All rights reserved.

Entangling of Peptide Nanofibers Reduces the Invasiveness of SARS-CoV-2.

The viral spike (S) protein on the surface of the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) binds to angiotensin-converting enzyme 2 (ACE2) receptors on the host cells, facilitating its entry and infection. Here, functionalized nanofibers targeting the S protein with peptide sequences of IRQFFKK, WVHFYHK and NSGGSVH, which are screened from a high-throughput one-bead one-compound screening strategy, are designed and prepared. The flexible nanofibers support multiple binding sites and efficiently entangle SARS-CoV-2, forming a nanofibrous network that blocks the interaction between the S protein of SARS-CoV-2 and the ACE2 on host cells, and efficiently reduce the invasiveness of SARS-CoV-2. In summary, nanofibers entangling represents a smart nanomedicine for the prevention of SARS-CoV-2.

Eco-Friendly Hierarchical Nanoporous Microfiber Respirator Filters Fabricated Using Rotary Jet Spinning Technology (RJS)

The current global health crisis caused by the SARS-CoV-2 virus (COVID-19) has increased the use of personal protective equipment, especially face masks, leading to the disposal of a large amount of plastic waste causing an environmental crisis due to the use of non-biodegradable and non-recyclable polymers, such as polypropylene and polyester. In this work, an eco-friendly biopolymer, polylactic acid (PLA), was used to manufacture hierarchical nanoporous microfiber biofilters via a single-step rotary jet spinning (RJS) technique. The process parameters that aid the formation of nanoporosity within the microfibers were discussed. The microstructure of the fibers was analyzed by scanning electron microscopy (SEM) and a noninvasive X-ray microtomography (XRM) technique was employed to study the three-dimensional (3D) morphology and the porous architecture. Particulate matter (PM) and aerosol filtration efficiency were tested by OSHA standards with a broad range (10-1000 nm) of aerosolized saline droplets. The viral penetration efficiency was tested using the phi X174 bacteriophage (similar to 25 nm) with an envelope, mimicking the spike protein structure of SARS-CoV-2. Although these fibers have a similar size used in N95 filters, the developed biofilters present superior filtration efficiency (similar to 99%) while retaining better breathability (<4% pressure drop) than N95 respirator filters.

Preparation of green-solvent-based polyamide nanofiber membrane and its air filtration performance

Objective The epidemic of COVID-19 and its variants is endangering human health. Wearing protective masks can effectively reduce the infection risk by resisting the inhalation of the polluted air containing the coronavirus. Electrospun polyamide nanofibers can be used as the core layer of protective masks and have lately received growing attention because of their high filtration performance and robust mechanical properties. However, existing electrospun polyamide nanofiber filters are usually prepared from toxic solvents which could cause severe environmental pollution and endanger workers' health, hence, their practical application should be restricted. Therefore, it is imperative to seek and develop green-solvent-based polyamide nanofiber filters. Method Innovative polyamide nanofiber filters were developed by direct electrospinning technique based on green solvents (Fig. 1). Ethanol as the solvent and water as the nonsolvent were adopted to prepare the green-solvent-based polyamide (GSPA) nanofibers by designing spinning solutions with different ethanol/water mass ratios (i.e., 10: 0, 9: 1, 8: 2, 7: 3, and 6: 4) . During electrospinning process, the working voltage, tip-to-collector distance, and solution extrusion speed were set as 30 kV, 15 cm and 1 mL/h, respectively. The nanofibers prepared with the different ethanol/water ratios were denoted as GSPA - 0, GSPA - 1, GSPA - 2, GSPA-3, and GSPA-4, respectively. Results It was found that water content had a great influence on the morphological structures of polyamide nanofibers (Fig. 2) - After introducing a small amount of water, the obtained GSPA - 1 nanofibers featuring thinner diameter of 332 nm were compared to the GSPA-0 nanofibers (499 nm). The enhanced conductivity (10. 5 μS/cm) of waterborne spinning solutions (Fig. 3) stimulated more charges on spinning jets and led to larger electrostatic force, thus greatly elongating the jets and thinning the fiber diameter. However, with the further increment of water concentrations from 20% to 40%, the obtained fibers exhibited an increased average diameter ranging from 443 to 1 553 nm, which was mainly attributed to the larger viscosity of spinning solutions. Although water cannot dissolve polyamide, homogenous waterborne polyamide/ethanol solutions can still be obtained with different ethanol/water mass ratios within a broad area in the stable region (Fig. 3) - The average pore size of GSPA -1 membranes decreased by 55% compared with that of GSPA-0 membranes, contributing to high filtration efficiency. Moreover, with different concentrations (10%, 20%, 30%) of water, the fluffy structure of GSPA nanofibers were achieved with a high porosity (> 80%), which would offer more passageways to transmit air rapidly. As the water concentration increased, the breaking strength of membranes increased at first and then decreased (Fig. 5), and the GSPA- 1 membranes exhibited the highest breaking strength of 5. 6 MPa, which was believed to be related to the enhanced entanglements and contacts among the adjacent fibers because of the small fiber diameter. The GSPA -1 membranes displayed the highest filtration efficiency (99. 02%) for the most penetration particles (PM0.3) by virtue of the small fiber diameter but suffered from poor permeability with a pressure drop of 158 Pa. Moreover, the GSPA- 1 membranes possessed the highest quality factor of 0. 029 3 Pa, suggesting the optimal filtration performance among different GSPA membranes. A high PM0.3 removal efficiency (>95%) was achieved for GSPA-1 filters under various airflow velocities ranging from 10 to 90 L/min (Fig. 7). Compared with conventional melt-blown fibers, the GSPA nanofibers featured a smaller diameter and higher Knudsen number (Fig. 8), and PM0.3 were captured mainly on the surfaces of green polyamide nanofibers (Fig. 9), demonstrating the higher adsorption ability benefiting from the larger specific surface area. Conclusion A cleaner production of polyamide nanofibers for air filtration was proposed by direct electrospinning based on green and sustaina le binary solvents of water and ethanol. For the first time, the structure including fiber diameter, porosity, and pore size of electrospun polyamide nanofibers were precisely tailored by manipulating water concentration in spinning solutions. The prepared environmentally friendly polyamide nanofiber filters feature the interconnected porous structure with the nanoscale ID building blocks (332 nm), mean pore size (0.7 μm), and porosity (84%), thus achieving efficient PM0.3 capture performance with the filtration efficiency of 99. 02% and pressure drop of 158 Pa, which could be comparable to previous toxic-solvent-processed nanofibers. Moreover, the GSPA nanofibers exhibit robust mechanical properties with an impressive breaking strength (5 . 6 MPa) and elongation (163. 9%), contributing to withstanding the external forces and deformation in the practical assembly and usage of resultant filters. It is envisaged that the green-solvent-based polyamide nanofibers could be used as promising candidates for next-generation air filters, and the proposed waterborne spinning strategy can provide valuable insights for cleaner production of advanced polyamide textiles. © 2023 China Textile Engineering Society. All rights reserved.

Nanofibrous Polymeric Membranes for Air Filtration Application: A Review of Progress after the COVID-19 Pandemic

Air pollution is one of the major global problems causing around 7 million dead per year. In fact, a connection between infectious disease transmission, including COVID-19, and air pollution has been proved: COVID-19 consequences on human health are found to be more severe in areas characterized by high levels of particulate matter (PM). Therefore, after the COVID-19 pandemic, the production of air filtration devices with high filtration efficiency has gained more and more attention. Herein, a review of the post-COVID-19 pandemic progress in nanofibrous polymeric membranes for air filtration is provided. First, a brief discussion on the different types of filtration mechanism and the key parameters of air filtration is proposed. The materials recently used for the production of nanofibrous filter membranes are presented, distinguishing between non-biodegradable polymeric materials and biodegradable ones. Subsequently, production technique proposed for the fabrication of nanofibrous membranes, i.e., electrospinning and solution blow spinning, are presented aiming to analyze and compare filtration efficiency, pressure drop, reusability and durability of the different polymeric system processed with different techniques. Finally, present challenges and future perspectives of nanofibrous polymeric membranes for air filtration are discussed with a particular emphasis on strategies to produce greener and more performant devices. © 2023 The Authors. Macromolecular Materials and Engineering published by Wiley-VCH GmbH.

A nanofiber Murray membrane with antibacterial properties for high efficiency oily particulate filtration

Particulate air pollution represented by PM2.5 is one of the biggest environmental challenges in the 21st century. Especially in 2020, the global outbreak of COVID-19 has brought new challenges to melt-blown filter materials, such as the attenuation of filtration efficiency with breathing, even no filtration effect for viruses as their smaller diameter, the sharp decline of filter efficiency after oily filtration cycle, and its limit in some explosive occasions. Here, using the diameter difference of polystyrene (PS), polyvinylidene fluoride (PVDF) and nylon 6(PA6) fibers, we report a multistage structure nanofiber membrane (PS/PVDF/PA6&Ag MSNMs) with high efficiency, low resistance and antibacterial effect by constructing gradient pore structure and introducing silver nanoparticles (Ag NPs), overcoming the above defects. The average filtration efficiency of PS/PVDF/PA6&Ag MSNMs for diisooctyl sebacate (DEHS) monodisperse particles from 0.2 μm to 4.9 μm was 99.88%, and the pressure drop was only 128 Pa. After repeated circulation for 100 times, the filtration efficiency and pressure drop remained stable. Above all, the antibacterial nanofiber membrane with high efficiency and low resistance has been preliminarily constructed, the future research will further focus on the performance after circulation. © 2023 Elsevier Ltd

Development of Carbon-Nanodot-Loaded PLA Nanofibers and Study of Their Barrier Performance for Medical Applications.

The COVID-19 pandemic has increased the usage of personal protective equipment (PPE) all round the world and, in turn, it has also increased the waste caused by disposable PPE. This has exerted a severe environmental impact, so in our work, we propose the utilization of a sustainable electrospun nanofiber based on poly lactic acid (PLA), as it is biobased and conditionally degradable. We optimized the weight percentage of the PLA-precursor solution and found that 19% PLA produces fine nanofibers with good morphology. We also introduced carbon nanodots (CNDs) in the nanofibers and evaluated their antibacterial efficiency. We used 1, 2, 3, and 4% CNDs with 19% PLA and found increased antibacterial activity with increased concentrations of CNDs. Additionally, we also applied a spunbond-nanofiber layered assembly for the medical face masks and found that with the addition of only 0.45 mg/cm2 on the nonwoven sheet, excellent particle filtration efficiency of 96.5% and a differential pressure of 39 Pa/cm2 were achieved, meeting the basic requirements for Type I medical face masks (ASTM-F2100).

A Review on Current Nanofiber Technologies: Electrospinning, Centrifugal Spinning, and Electro‐Centrifugal Spinning

Nanofiber‐based products are widely used in the fields of public health, air/water filtration, energy storage, etc. The demand for nonwoven products is rapidly increasing especially after COVID‐19 pandemic. Electrospinning is the most popular technology to produce nanofiber‐based products from various kinds of materials in bench and commercial scales. While centrifugal spinning and electro‐centrifugal spinning are considered to be the other two well‐known technologies to fabricate nanofibers. However, their developments are restricted mainly due to the unnormalized spinning devices and spinning principles. High solution concentration and high production efficiency are the two main strengths of centrifugal spinning, but beaded fibers can be formed easily due to air perturbation or device vibration. Electro‐centrifugal spinning is formed by introducing a high voltage electrostatic field into the centrifugal spinning system, which suppresses the formation of beaded fibers and results in producing elegant nanofibers. It is believed that electrospinning can be replaced by electro‐centrifugal spinning in some specific application areas. This article gives an overview on the existing devices and the crucial processing parameters of these nanofiber technologies, also constructive suggestions are proposed to facilitate the development of centrifugal and electro‐centrifugal spinning.

Evaluation of biocidal properties of biodegradable nanofiber filters and their use in face masks.

Due to the recent coronavirus-2019 pandemic, several studies have emerged looking for new materials, especially with biocidal characteristics. Thus, the present research investigates the antibacterial properties of biodegradable cellulose acetate (CA) / cetylpyridinium bromide (CPB) electrospun nanofibers, their aerosol filtration, and the possible use as a filter media of surgical face masks. Then, samples of these nanofibers were produced over a nonwoven substrate, using different volumes of polymeric solution during the electrospinning process. The evaluation of the antibacterial properties of the nanofibers was performed for Escherichia coli and Staphylococcus aureus using quantitative methods. The aerosol filtration performance was evaluated in these samples for NaCl nanoparticles (from 7-300 nm) and with 8 mL min-1 of air flow rate. The results show that the single use of the surfactant has antibacterial properties from a concentration of 39 µg mL-1 of solution. The nanofibers presented a reduction of 100% for both bacteria. Air filtration tests showed 126.03 and 207.73 Pa cm-² of pressure drops and 63 and 77% of aerosol filtration efficiency (FE) for samples with 0.13 and 0.15 mL, respectively. Regarding the nanofiber produced with 0.35 mL, the value obtained was 115.13 ± 33.64 Pa cm-2 and 3.15% of particle penetration. These breathability values are higher than those required for the surgical face mask standard, indicating that improvements in the porosity and thickness are necessary to meet the Brazilian requirements. However, the nanofibers could be applied as filter media for indoor air conditioning systems due to their FE and biocidal properties.

Preparation, characterization, and air filtration property of electrospun bimodal fibrous membrane based on low conductivity blended polymers solution

One–step preparation of electrospun bimodal fibrous membrane based on single nozzle is the key to the efficient fabrication of high–performance air filter. However, the preparation mechanism of electrospun bimodal fibers at low conductivity solution system is not clear, and there is a lack of evaluation methods for the quality of bimodal nanofibers, which limits the applicability of single nozzle electrospinning and the preparation efficiency of electrospun bimodal fibers. Here, three electrospinning processes at low conductivity solution systems of polyamide–6 (PA6), PA6 blended PVP (PA6/PVP), and PA6 blended polyethylene oxide (PA6/PEO) were studied according to the rheological properties and the fluid electrics (i.e., zeta potential), and the quality of the prepared bimodal fibrous membrane was creatively evaluated by R value. Inhomogeneous phase separations of the electrospinning jet along the direction parallel (x–axis) or perpendicular (y–axis) to the electric field were responsible for the formation of bimodal fibers. In addition, for the same solution system, the R value had a positive correlation with the air filtration performance. This work will greatly enhance the applicability of one–step single nozzle electrospinning for the preparation of bimodal nanofibers, improve the preparation efficiency, and promote the development of high–performance air filter. © 2022 Elsevier Ltd

Biobased polymer SF/PHBV composite nanofiber membranes as filtration and protection materials

With the emergence of the COVID-19, masks and protective clothing have been used in huge quantities. A large number of non-degradable materials have severely damaged the ecological environment. Now, people are increasingly pursuing the use of environmentally friendly materials to replace traditional chemical materials. Silk fibroin (SF) and Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) have received increasing attention because of their unique biodegradability and biocompatibility. In this paper, a series of biodegradable SF/PHBV nanofiber membranes with different PHBV content were fabricated by using electrospinning technology. The morphology of the electrospun SF/PHBV composite nanofiber was observed by scanning electron microscopy (SEM). The average diameters of the pure SF, SF/PHBV (4/1), SF/PHBV (3/1), and SF/PHBV (2/1) nanofibers were 55.16 ± 12.38 nm, 75.93 ± 21.83 nm, 69.35 ± 21.55 nm, and 61.40 ± 12.31 nm, respectively. Fourier transform infrared (FTIR) spectroscopy and X-ray diffraction (XRD) were used to explore the microstructure of the electrospun SF/PHBV composite nanofiber. The crystallization ability of the composite nanofiber was greatly improved with the addition of PHBV. The results of thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) indicated that the thermal stability of SF was better than PHBV obviously, so SF could improve the thermal stability of the composite materials within a certain range. The mechanical properties of the electrospun nanofiber membranes were evaluated by using a universal testing machine. In general, the elongation of the composite nanofiber membranes decreased, and the breaking strength increased with the addition of PHBV. The small pore size of the nanofiber membranes ensured that they had good application prospects in the field of filtration and protection. When the spinning time was 1 h, the filtration efficiency of SF/PHBV/PLA composite materials remained above 95%. © 2021 The Textile Institute.

P(VDF-TrFE)/BaTiO3 Nanofibrous Membrane with Enhanced Piezoelectricity for High PM0.3 Filtration and Reusable Face Masks.

In the background of air pollution and regular COVID-19 prevention, personal protective masks are necessary for our daily life. However, protective masks with high PM0.3 filtration usually have poor air permeability and are mostly disposable, leading to a heavy burden on the environment. In this work, a reusable membrane based on piezoelectric poly(vinylidene fluoride-trifluoroethylene) [P(VDF-TrFE)] nanofibers embedded with BaTiO3 nanoparticles (BTO NPs) was developed. The P(VDF-TrFE)/BTO composite nanofibers not only have enhanced piezoelectricity and surface polarity but also have reduced diameters that could be beneficial for electrostatic adhesion, pole-polar interactions, and mechanical sieving to increase the PM0.3 capture capacity. Moreover, the BTO NPs also improved the charge storage capacity of the composite membrane, which could further enhance the PM0.3 filtration efficiency after corona treatment. The piezoelectric mask based on P(VDF-TrFE)/BTO composite nanofibers has high filtration efficiencies of 96% for PM0.3 and 98% for bacteria, while the pressure drop was only 182 Pa, which is lower than the commercial N95 standard of 343.2 Pa. Furthermore, the piezoelectric mask has a long and stable filtration performance after 5 cycles of 75% alcohol disinfection, demonstrating that the P(VDF-TrFE)/BTO composite membrane has a potential application in personal protective masks with comfortable and reusable properties.

Electrospun Filtering Membrane Designed as Component of Self-Decontaminating Protective Masks.

The 2019 coronavirus outbreak and worsening air pollution have triggered the search for manufacturing effective protective masks preventing both particulate matter and biohazard absorption through the respiratory tract. Therefore, the design of advanced filtering textiles combining efficient physical barrier properties with antimicrobial properties is more newsworthy than ever. The objective of this work was to produce a filtering electrospun membrane incorporating a biocidal agent that would offer both optimal filtration efficiency and fast deactivation of entrapped viruses and bacteria. After the eco-friendly electrospinning process, polyvinyl alcohol (PVA) nanofibers were stabilized by crosslinking with 1,2,3,4-butanetetracarboxylic acid (BTCA). To compensate their low mechanical properties, nanofiber membranes with variable grammages were directly electrospun on a meltblown polypropylene (PP) support of 30 g/m2. The results demonstrated that nanofibers supported on PP with a grammage of around only 2 g/m2 presented the best compromise between filtration efficiencies of PM0.3, PM0.5, and PM3.0 and the pressure drop. The filtering electrospun membranes loaded with benzalkonium chloride (ADBAC) as a biocidal agent were successfully tested against E. coli and S. aureus and against human coronavirus strain HCoV-229E. This new biocidal filter based on electrospun nanofibers supported on PP nonwoven fabric could be a promising solution for personal and collective protection in a pandemic context.

Development and clinical evaluation of commercial glucose meter coupled with nanofiber based immuno-platform for self-diagnosis of SARS-CoV-2 in saliva

Rapid diagnostics for the diagnosis of COVID-19 are urgently needed in offices, residences, and other public places due to the new Covid epidemic stages. A portable and easy-to-use immunosensing platform was developed and evaluated for a point-of-care and self-detection of SARS-CoV-2 spike protein without the need for extraction, separation, or amplification steps using clinically isolated samples (n = 40 samples). The sensing platform was fabricated based on functionalized nylon nanofibrous membranes and a commercial glucose meter to enable easy deployment of the sensing technology. The fabrication of the immunoreaction vial using nylon nanofibrous membranes as a support matrix for the tethering of antibodies significantly improved the sensitivity of the detection platform in contrast to the use of conventional nylon casted membranes. The sensitivity of the nanofibrous membrane attached antibody was at least an order of magnitude higher (∼12 times) compared to the sensitivity of detection with regular casted membrane-based immunoreaction vial. The feasibility of the designed sensing platform was investigated using saliva as a non-invasive and self-administered sample for the diagnosis of SARS-CoV-2. With a detection limit of 9 ng mL−1 and no pretreatment processes required, the sensing platform demonstrated its suitability for the direct detection of SARS-CoV-2 spike protein in the spiked saliva samples. In addition, the developed platform depicted high agreement with RT-qPCR data in the analysis of the clinical samples with good stability over the storage time and reusability for three cycles with maintaining more than 95% of its original activity. [Display omitted] • Diagnosis of COVID-19 in human saliva using commercial glucose meter. • High sensitivity with broad dynamic range was achieved using nanofibrous membrane. • Successfully analyzing of clinical samples in agreement with RT-qPCR. • Potential application for self- and on-site diagnosis without sample pretreatment. • The sensing platform depicted reusability for 3 cycles and good storage stability. [ FROM AUTHOR]